Film capacitors - Power Electronic Capacitors
MKP PEC DC
Series/Type: B2562X
Ordering code: B25620-S1457-K102
Date: 8/2/2012
Version: 3.0Film capacitors – Power Electronic Capacitors B25620-S1457-K102
MKP PEC DC B2562X
Preliminary data
CHARACTERISTICS
C 450 µF
N
Tol. ± 5% %
U 1200 V
NDC DC
I * 50 A
max
L < 60 nH
self
Tan (cid:1) o 2 · 10-4
R 1,2 m(cid:2)
S
TEST DATA
U 1,5 . U , 10 s
TT NDC
U TC 2 . (U NDC / 2 ) + 1000V, 10 s
R . C (cid:3) 10000 s
is
tan (cid:1) (100Hz) (cid:4) 1 · 10-3
CLIMATIC CATEGORY (55/60/56)
Q - 55 °C
min
Q * + 60 °C
max
Q + 75 °C
HS
Q - 55…+ 85 °C
stg
Rel. Humidity (cid:4) 95 %
t 100 000 h @ 45ºC
LD (co)
26 500 h @ 60˚C
Max. Altitude 2000 m
Cooling Naturally
*CURRENT DERATING
Q = + 75 °C / Natural convection GENERAL DATA
HS
Dimensions D x H 116 x 95 mm
Current Derating @ Ths = 75 °C
Approx. Weight 1100 g
60
55 Resin filling Hard Polyurethane
50 Fixing M12 stud on bottom
45
Max fixing torque 12 Nm
40
45 50 55 60 65 Terminals Female M6
Temp. (°C) Max terminal torque 8 Nm
MKP - metallized polypropylene capacitor
Self healing, Dry type, Non PCB
Aluminum case plus plastic top disc UL94 V2
Standard IEC 61071 / RoHS Compliance
FK EPC 8/2/2012
Please read Cautions and warnings and Page 2 of 3
Important notes at the end of this document.
)A(
xamI
Expected Lifetime @ Ths
1
0,975
0,95
0,925
0,9
0,5 0,7 0,9 1,1 1,3 1,5
tld/tld(co)
nU/U
45°C 50°C 60°CImportant notes
The following applies to all products named in this publication:
1. Some parts of this publication contain statements about the suitability of our products for
certain areas of application. Thesestatements arebased onour knowledgeof typicalrequirements
that are often placed on our products in the areas of application concerned. We nevertheless
expressly point out that such statements cannot be regarded as binding statements about the
suitability of our products for a particular customer application. As a rule, EPCOS is either
unfamiliar with individual customer applications or less familiar with them than the customers
themselves. For these reasons, it is always ultimately incumbent on the customer to check and
decide whether an EPCOS product with the properties described in the product specification is
suitable for use in a particular customer application.
2. Wealsopointoutthatinindividualcases,amalfunctionof electroniccomponents or failure
before the end of their usual service life cannot be completelyruled out in the current state of
the art, even if they are operated as specified. In customer applications requiring a very high level
of operational safety and especially in customer applications in which the malfunction or failure of an
electronic component could endanger human life or health (e.g. in accident prevention or life-saving
systems), it must therefore be ensured by means of suitable design of the customer application or
other action taken by the customer (e.g. installation of protective circuitry or redundancy) that no
injury or damage is sustained by third parties in the event of malfunction or failure of an electronic
component.
3. The warnings, cautions and product-specific notes must be observed.
4. In order to satisfy certain technical requirements, some of the products described in this
publication may contain substances subject to restrictions in certain jurisdictions (e.g.
because they are classed as hazardous). Useful information on this will be found in our Material
Data Sheets on the Internet (www.epcos.com/material). Should you have any more detailed