Danger
This symbol indicates the presence of dangerous voltage within and outside the product enclosure that
may constitute a risk of electric shock, serious injury or death to persons if proper precautions are not
followed.
Caution
This symbol alerts the user to the presence of hazards that may cause minor or moderate injury to
persons, damage to property or damage to the device itself, if proper precautions are not followed.
Note
This symbol directs the user’s attention to important installation, operating and maintenance instructions.
Installation Considerations
Installation and maintenance of the ION 8000 series meter should only be performed by qualified, competent
personnel that have appropriate training and experience with high voltage and current devices. The meter must be
installed in accordance with all Local and National Electrical Codes.
DANGER
Failure to observe the following instructions may result in severe injury or death.
(cid:139)During normal operation of the ION 8000 series meter, hazardous voltages are present on its terminal
strips, and throughout the connected potential transformer (PT), current transformer (CT), digital (status)
input, control power and external I/O circuits. PT and CT secondary circuits are capable of generating
lethal voltages and currents with their primary circuit energized. Follow standard safety precautions while
performing any installation or service work (i.e. removing PT fuses, shorting CT secondaries, etc).
(cid:139)The terminal strips on the meter base should not be user-accessible after installation.
(cid:139)Do not use digital output devices for primary protection functions. These include applications where the
devices perform energy limiting functions or provide protection of people from injury. Do not use the ION
8000 series in situations where failure of the devices can cause injury or death, or cause sufficient energy
to be released that can start a fire. The meter can be used for secondary protection functions.
(cid:139)Do not HIPOT/Dielectric test the digital (status) inputs, digital outputs, or communications terminals. Refer
to the label on the ION 8000 series meter for the maximum voltage level the device can
withstand.
CAUTION
Observe the following instructions, or permanent damage to the meter may occur.
(cid:139)The ION 8000 series meter offers a range of hardware options that affect input ratings. The ION 8000
series meter’s serial number label lists all equipped options. Applying current levels incompatible with the
current inputs will permanently damage the meter. This document provides installation instructions appli-
cable to each hardware option.
(cid:139)The ION 8000 series meter’s chassis ground must be properly connected to the switchgear earth ground
for the noise and surge protection circuitry to function correctly. Failure to do so will void the warranty.
(cid:139)Terminal screw torque: Barrier-type (current, voltage, and relay terminal screws: 1.35 Nm (1.00 ft-lbf)
max. Captured-wire type (digital inputs/outputs, communications, power supply: 0.90 Nm
(0.66 ft.lbf) max.
FCC Notice
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15
of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the
equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference at his own expense.
3The Ringer Equivalence Number (REN) for the ION 8000 series optional internal modem is 0.6. Connection to the
ION 8000 series internal modem should be made via an FCC Part 68 compliant telephone cord (not supplied). The
ION 8000 series cannot be used on a public coin phone service or party line services.
Network Compatibility Notice for the Internal Modem
The internal modem in meters equipped with this option is compatible with the telephone systems of most countries
in the world, with the exception of Australia and New Zealand. Use in some countries may require modification of the
internal modem’s initialization strings. If problems using the modem on your phone system occur, please contact
Power Measurement Technical Services
Standards Compliance
Limitation of Liability
Power Measurement Ltd. (“Power Measurement”) reserves the right to make changes in the device or its
specifications identified in this document without notice. Power Measurement advises customers to obtain the
latest version of the device specifications before placing orders to verify that the information being relied upon
by the customer is current.
Regardless of whether any remedy set forth herein fails of its essential purpose, except to the extent the following
limitation is prohibited by applicable law, Power Measurement shall not, in any event or under any legal claim
or theory (whether based on contract, indemnity, warranty, tort (including negligence and strict liability) or
otherwise), be liable to the original purchaser or any other person or entity for special, indirect, incidental,
punitive, liquidated, special or consequential damages whatsoever with respect to any purchased product,
including, without limitation, business interruption, loss of use, profit or revenue, even if Power Measurement has
been advised of the possibility of such damages. To the extent that a limitation or exclusion of consequential
damages are prohibited by applicable law, then Power Measurement’s liability shall be limited to twice the
amount of the relevant purchased product. Not to limit the foregoing, a) Power Measurement shall not be liable
for any claim (other than a claim solely for the breach of one of the above Warranties that is made in accordance
with the above described procedures) made by the original purchaser, its employees, agents, or contractors for
any loss, damage, or expense incurred due to, caused by, or related to any purchased product; and b) the above
Warranties are the original purchaser's exclusive remedy and Power Measurement hereby expressly disclaims all
other warranties, express or implied, including, without limitation, warranties of non-infringement and the
implied warranties of merchantability and fitness for a particular purpose.
These limited Warranties shall not apply to any product that has been subject to alteration, accident, misuse,
abuse, neglect or failure to exactly follow Power Measurement's instructions for operation and maintenance. Any
technical assistance provided by Power Measurement's personnel or representatives in system design shall be
deemed to be a proposal and not a recommendation. The responsibility for determining the feasibility of such
proposals rests with the original purchaser and should be tested by the original purchaser. It is the original
purchaser’s responsibility to determine the suitability of any product and associated documentation for its
purposes. The original purchaser acknowledges that 100% "up" time is not realizable because of possible
hardware or software defects. The original purchaser recognizes that such defects and failures may cause
inaccuracies or malfunctions. Only the terms expressed in these limited Warranties shall apply and no
distributor, corporation or other entity, individual or employee of Power Measurement or any other entity is
authorized to amend, modify or extend the Warranties in any way.
The information contained in this document is believed to be accurate at the time of publication, however, Power
Measurement assumes no responsibility for any errors which may appear here and reserves the right to make
changes without notice.
Power Measurement, ION, ION Enterprise, MeterM@il, WebMeter and “smart energy everywhere” are either
registered trademarks or trademarks of Power Measurement. All other trademarks are property of their respective
owners.
Covered by one or more of the following patents:
U.S. Patent No's 6825776, 6813571, 6798191, 6798190, 6792364, 6792337, 6751562, 6745138, 6737855,
6694270, 6687627, 6671654, 6671635, 6615147, 6611922, 6611773, 6563697, 6493644, 6397155,
6186842, 6185508, 6000034, 5995911, 5828576, 5736847, 5650936, D459259, D458863, D443541,
D439535, D435471, D432934, D429655, D429533, D427533.
4ION 8000 Series Models
Socket Meter
The socket meter is designed to fit into S-Base meter sockets and A-to-S Base

您好！关于关口计量ION8000系列的详细操作手册，这是一个专门针对ION8000系列电力关口计量设备的操作指南。这款产品可能包含了高级的电能计量、实时监控和数据管理功能，用于电力系统的输配环节，确保电能质量和交易的准确性。 通常，操作手册会包含以下内容： 1. **设备介绍**：产品的基本概述，包括型号、功能特性以及适用环境。 2. **安装步骤**：指导用户如何安全地安装和定位设备。 3. **接线图与接口说明**：详细列出各个端口的功能和连接方式。 4. **开机与初始化**：如何正确启动设备并进行初次设置。 5. **操作流程**：提供日常使用中的操作方法，如数据采集、设置参数、故障排查等。 6. **功能演示**：可能包含视频教程或图文示例，帮助用户理解复杂功能。 7. **维护保养**：设备的清洁、检查和定期维护建议。 8. **故障排除**：常见问题的解决方法和故障代码解读。 为了获取最准确的信息，建议您直接查阅官方提供的操作手册，或者联系我们的技术支持团队，他们可以提供专业的在线指导。如果您在阅读过程中遇到任何疑问，也可以随时告诉我，我会尽力帮助您解答。